Cbeam Software
.C-Beam Machine Electrical Assembly Instructions.4.1.2 Wire Routing.24 4.1.3 Connecting the CNC-xPro.26 Software & Machine Settings 4.2.1 Installing Universal G-Code Sender (UGS).27 4.2.2 Configuring The Firmware.28 Testing Complete Appendix Appendix A - Kit Contents Appendix B Recommended GRBL Settings C-Beam Machine.1.0 Getting Started C-Beam Machine Getting Started.In many projects it happens, that an off the shelf plate does not suit your needs, a C-Beam machine is the solution to this problem. A C-Beam Machine offers the freedom to create the custom plates you need, right away, no long waits, no extortionate prices.Motor-Ferrite's on the motor wires as close as possible to the CNC-xPro. Clip the PSU- Output-Ferrite's on the PSU-Output-Power-Cable as close as possible to the 24V-360W- Power-Supply. And the Router-Ferrite, as close as to your router as possible. C-Beam Machine Getting Started.2.0 Power Supply Assembly C-Beam Machine Power Supply Assembly.B. Secure each XT-Male connector using 2 x Plastite-Screw-M2.5-8mm through the holes provided on the securing tab as seen on the internal view. When initially placing the screw, it is helpful to hold each screw in place using tweezers or long nose pliers.
C-Beam Machine Power Supply Assembly.2.1.2 Inserting LED-Volt-Meter A. Gently push the LED-Volt-Meter into the provided gap on the top of the PSU Cover.
The wires on the LED-Volt-Meter should be oriented to the front of the PSU-Cover. C-Beam Machine Power Supply Assembly.2.2 Input 2.2.1 IEC-Inlet Wires A. Attach the receptacle end of the IEC-Inlet-Live-Wire, IEC-Inlet-Neutral-Wire & IEC- Inlet-Earth-Wire to their respective terminal tabs on the IEC-Inlet, as seen in the above image. C-Beam Machine Power Supply Assembly.2.2.2 Attaching IEC-Inlet A. Secure the assembled IEC-Inlet to the PSU-Cover using 2 x Plastite-Screw-M3-8mm. Ensure the switch is on the right hand side.
C-Beam Machine Power Supply Assembly.2.3 Connecting PSU-Cover 2.3.1 Connecting Wires C-Beam Machine Power Supply Assembly.D. Finally, connect the three IEC-Inlet wires to the 24V-360W-Power-Supply. The IEC- Inlet-Earth-Wire is very inflexible compared to the previous ones, so this wire may take some force to get into position. C-Beam Machine Power Supply Assembly.B. On each side, secure the PSU-Cover using two Plastite-Screw-M3-8mms. Go through the slots on the metal casing of the 24V-360W-Power-Supply, and then into the holes on the PSU-Cover.
C-Beam Machine Power Supply Assembly.LCD can be used to adjust the volt- age. Use a screwdriver to adjust the voltage to 24.0, and take caution to not touch any metal parts with the screwdriver. C-Beam Machine Power Supply Assembly.2 x M4-Cap-Head-6mm Bolts. The longest side of each PSU-Mount goes against the 24-360W-Power-Supply. Bring the 24-360W-Power-Supply to the rear left of the C-Beam Machine, and secure it through the PSU-Mounts to the top of the V-Slot-2060-500mm using 2 x M5-Low- Profile-8mm Bolts, and 2 x M5-Tee-Nuts, these have to be inserted from the end of the extrusion.3.0 CNC xPro Assembly C-Beam Machine CNC xPro Assembly.A. Attach the Terminal-Block to the CNC-xPro-Mount using 4 x M3-Cap-Head-16mm Bolts. Tighten the M3-Cap-Head-16mm Bolts to M3-Nyloc-Nuts on the other side of the CNC-xPro-Mount.
Double check that the Terminal-Block is mounted to the correct side of the CNC-xPro-Mount. C-Beam Machine CNC xPro Assembly.CNC-xPro-Fan-Mount. Make sure that the power wires on the 30mm-24V-DC-Fans are both on the same side of the CNC-xPro-Fan-Mount. C-Beam Machine CNC xPro Assembly.Nyloc-Nut. The CNC-xPro-Fan-Mount should be orientated so the power wires are on the same side as the Terminal-Block. The CNC-xPro should be orientated so the USB terminal is in the same position as shown by the red square above. C-Beam Machine CNC xPro Assembly.50mm of the black sheaving from the bare end to expose the red and black wires underneath.
Strip back approximately 20mm of the sheaving from the red and black wires to expose the copper core underneath. Connect these wires to the Terminal-Block as in Step B. C-Beam Machine CNC xPro Assembly.3.0.5 Mounting the CNC-xPro Assembly C-Beam Machine CNC xPro Assembly.It should be towards the right hand side of the C-Beam-Machine-Gantry (If looking from the back), as seen in the images above. Screw each M5-Low-Profile-50mm bolt to engage the M5-Drop-In-Tee-Nut with the slot.
Fully tighten each M5-Low-Profile-50mm bolt. C-Beam Machine CNC xPro Assembly.4.0 Wiring & Commissioning C-Beam Machine Wiring & Commissioning.B. Repeat Step A for a Wire-Clips-Motor-80mm, shown in the Red Square above. Repeat Step A for a Wire-Clips-Power-60mm, shown in the Green Square above. Repeat Step A for 2 x Wire-Clips-Motor-80mm, shown in the Blue Squares above. C-Beam Machine Wiring & Commissioning.Bring them up the right hand column towards the CNC-xPro.
Secure them both to the Wire-Clips-Power-60mm. The spare position on the Wire-Clips-Motor-60mm and Wire-Clips-Motor-80mm’s can be used for the router wire, or any other wire you need to safely secure. C-Beam Machine Wiring & Commissioning.B. Connect the 3 x NEMA23-Stepper-Motors to the CNC-xPro as shown above. Take note of the order of the wire colours. If interested, it is a good idea to read the CNC-xPro Wiki for more in-depth informa- tion: C-Beam Machine Wiring & Commissioning.G.
On the ‘Port’ drop down list find the CNC-xPro, it should look similar to what is selected in the image above. Once found click ‘Open’ and UGS should successfully connect to the CNC-xPro. The Console output will show information similar to the above. C-Beam Machine Wiring & Commissioning.For instance, setting number 100 is incorrect when compared to Appendix B, correct it by entering $100 = 200.
Do this for all the settings in Appendix B. If interested, it is a good idea to read the GRBL Firmware Wiki for more in-depth infor- mation: C-Beam Machine Wiring & Commissioning.ACME-Lead-Screw are attached correctly, aligned, and not binding. If the assembly is correct, it may be that the drivers on the CNC-xPro are overheating, so try decreasing the current in 1/8th turns. C-Beam Machine Wiring & Commissioning.Clip the PSU-Output-Ferrite's on the PSU-Output-Power-Cable as close as possible to the 24V-360W-Power-Supply. And the Router-Ferrite, as close as to your router as possible. Furthermore if you have a dust extraction system, we recommended grounding the extraction hose along its length using a metal strip. C-Beam Machine Wiring & Commissioning.This allows you to get used to the machine in a safe manor.
Cbeam Software
Is Cream A Audit Software
To prevent crushing the pen, work on only one plane in your CAM package and have no negative Z Movements.